Your Phone (required)

Only samples 3 and 8 were broken on the retreating side. The tensile strength values of different samples are presented in Table 3. Subject https://doi.org/10.1007/s00170-015-6843-6, DOI: https://doi.org/10.1007/s00170-015-6843-6, Over 10 million scientific documents at your fingertips, Not logged in Figure 7. Int J Adv Manuf Technol 61(1–4):195–204, Magnabosco I, Ferro P, Bonollo P, Arnberg L (2006) An investigation of fusion zone microstructures in electron beam welding of copper- stainless steel. The metallographic organization of H62 copper alloy modified layer was analyzed using an MDS400 inverted metallographic microscope produced by Chongqing aut Optical Instrument Co., Ltd (China).

For example: Brass is usually a warm golden color. The brass supplier from China default brass option is H59. In comparison, bronze is principally an alloy of copper and tin. Mater Manuf Process 25(11):1227–1232, Shi YW, Zhong F, Li XY, Gong SL, Chen L (2007) Effect of laser beam welding on tear toughness of a 1420 aluminum alloy thinsheet.

The technological parameters used in the FSSP process were as follows. Mater Des 32(10):5127–5131, Torkamany MJ, Sabbaghzadeh J, Hamedi MJ (2011) Effect of laser welding mode on the microstructure and mechanical performance of dissimilar laser spot welds between low carbon and austenitic stainless steels. 5crnimo Alloyed Tool Steel Hot Rolled Bar. The inhibitory effect of strong electric field on H62 brass plate under high temperature deformation. Google Scholar, Luo J, Wang XM, Liu DJ, Li F, Xiang JF (2012) Inertia Radial Friction Welding Joint of Large Size H90 Brass/D60 Steel Dissimilar Metals. Metallographic organization of the modified surface of different samples: (a) sample 1, (b) sample 2, (c) sample 3, (d) sample 4, (e) sample 5, (f) sample 6, (g) sample 7, (h) sample 8, and (i) sample 9.

This was because the higher the pressure during the modification process, the higher the temperature, and the more refined the grain, the finer the grain. Hence, the tensile strength was larger. Wang14 et al. | All Rights Reserved. Therefore, the grain size was refined by increasing the temperature. Brass H62 consists mainly of two elements: copper and zinc; copper accounts for 62%. Members of _ can log in with their society credentials below, Weiwei Song, Xiaojing Xu, Shengrong Liu, Jiafei Pu, and Hongfeng Wang, https://creativecommons.org/licenses/by-nc/4.0/This article is distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 License (. Copyright © JS Havens Metal Products Co.,Ltd All Rights Reserved. Hence, despite surface grain refinement, the tensile strength was weakened. Figure 3((d) to (f)) shows that under the same technological parameters, the grain refinement degree on the surface of the modified layer increased with the increase in pressure and the grain size of the modified layer after two passes of modification. Defects such as pores, cracks, and oxides often exist in the coating tissues obtained by plasma spraying, which to a large extent limit the application of plasma spraying technology.16 Li17 et al. The higher the copper content, the higher the unit price and the lower the copper content, the lower the unit price.

H62 datasheet, cross _ g 6# Contact Foot 6 H62 Brass T , 10.0 PCB Layout Top View A A No. These requirements for the performance of H62 copper alloy are higher, especially for the connection of H62 copper alloy pipes.

The surface of copper alloy was modified to improve its wear resistance, corrosion resistance, and tensile strength. The elements in stainless steel and brass had homogeneous distribution and mixing.

The preliminary test force of the head was 10 kg, the main test force was 90 kg, the total test force was 100 kg, and the loading and unloading time was 10 s. Each test point selected three points near its center and took the mean as the hardness value of this point. The study adopted the NN universal tensile testing machine produced by Shanghai New San Si Measuring Instrument Manufacturing Co., Ltd. (China) for stretching experiments and S-3400N tungsten filament scanning made by Japan Hitachi Co., Ltd. Five tensile samples were selected under each parameters, and the average value of the tensile values of the five samples was taken as the tensile value of the tensile samples under this parameter. (a) FSSP equipment and (b) The tool of stirring. Hardness of the modified surface of different samples.

SEM photos of the modified surface of different samples: (a) sample 1, (b) sample 2, (c) sample 3, (d) sample 4, (e) sample 5, (f) sample 6, (g) sample 7, (h) sample 8, and (i) sample 9. By continuing to browse