However there are a certain number of applications which need to use incoming connections as well in order to function properly, which means that the connection is being initiated by the other host computer, not by yours. As long as any one of the following conditions is met, it means the port mapping is correctly done (and thus you have on open listening port): Copyright © 2003-2010 BitComet. When your router opens a port in its firewall, this is a potential security hole. With that said, if you do the following you should end up with around the best possible speeds: BitComet requires you to be able to receive incoming connections.

If after that you find that you are still in a firewalled state (i.e. Sometimes, UPnP Auto Port Mapping just won't work. تم تعطيل الجافا سكربت. Next, in windows, click Start then Run Type cmd and press enter. After that you will forward the listen port, on Router1 (the modem), towards the IP you assigned to the WAN interface of Router2. You can check proxy settings here (you may have a problem if doesn’t display the IP address that your ISP has assigned you at the top of the page or as 「X-Forwarded-For」). You should use IP addresses from the ranges available on your specific devices. XYZ will be forwarded to THAT specific IP of the LAN.”. The thing you need to understand is that NAT (Network Address Translation) will need to be performed twice before any IP packet will reach from the Internet to any of your PCs or from your PCs to the Internet. This way the listen port will be forwarded all the way from the public IP of the WAN interface on Router1 to the LAN NIC card of your PC. Under “Network tasks” on your left panel, click on “View Network connections”. Again, it’s best to choose a number between 49152 and 65534. In fact BitComet is one of the friendlier clients for users who are blocked by routers. By default your computer uses a dynamic (changeable) IP address, which it obtains by request from whatever it's Ethernet adapter is connected to. If anything goes wrong you can always reset the router to factory defaults by holding the reset button on the back for at least 10 seconds (the exact interval is specified in your manual). From one of Router1's LAN (Ethernet) ports (often there is only one), usually, another Ethernet cable emerges which is plugged into the other router/switch device's WAN port (or router/switch/wireless-access point). This technology can find more seeds to help finish your downloads. most likely your Internet connection will be firewalled at the ISP site by default (so you basically get only half of an Internet connection, without the possibility of successful incoming connections). You may need to download version 2.0 now from the Chrome Web Store. le secret d'un telechargement optimale d'un torrent est de savoir configurer le port forwarding. BT Hubs are configured to handle that data transmission automatically, but sometimes you may want to create your own port forwarding rules. Completing the CAPTCHA proves you are a human and gives you temporary access to the web property. LAN users check whether port mapping is successfully set. How to check whether UPnP devices are successfully enabled: Note: If you arrived in this section of the guide through a link (without reading the Introduction for this topic) make sure you understand the note at the very top of this page, regarding users with Internet connections established through wireless modems that use mobile telco technology, before proceeding further with the configuration steps below. License To configure port forwarding, open up BitComet and go to Options > Preferences. It's easy to get answers to your questions: How do I set up port forwarding on my BT Hub? Step 1: Click on Start —> Run —> Type cmd —> press Enter or OK —> at the command prompt type ipconfig/all —> press Enter. Remember you need to save any changes you make. Make sure you scroll all the way down the list and look at all of them. Since more and more devices come in integrated combo models, modem/router, modem/router/switch or modem/router/switch/wireless-access point devices are very common these days.

Switching to another client like uTorrent or Azureus will not help fix the issue of getting slow torrent speeds. If you have a mix of Remote and Local like the picture above, it’s a sign that your port forwarding is configured properly already (probably done automatically via UPnP) ¡X so skip to the next section. But if you are behind a router or use Windows Internet Connection Sharing (ICS) or you are behind a firewall, you might need to make some adjustments before you get rid of the infamous yellow light and BitComet works as intended. It should show you something similar to this: 「IP Address」 is your computers IP address that you need to forward the port to. But because there are so many routers and they’re all different, I can’t explain step-by-step how to configure port forwarding in your exact model. 變更 ). In this topic we will discuss the configuration of the router (port forwarding) both automatic (through UPnP) and manual, to the end of opening a port in your router's firewall and forwarding it on the setup page of your router, for BitComet. And once again, thanks to this guide for showing me how. Be it for the purpose of adding wireless capabilities to the LAN or for increasing the number of available Ethernet ports on the LAN in order to add several computers or for whatever other reasons, many users find themselves using two cascaded routers (many of them unknowingly!). Once you've completed the steps at portforward.com, your BitComet Short of contacting your ISP to ask if there is a possibility to get full Internet connections on the same device or changing your Internet subscription plan for one that has incoming connections unfirewalled by default (all xDSL, cable or FiOS providers usually offer unfirewalled connections), there is nothing you can do on your side to unblock incoming connections, therefore there is no point in following this guide or any other port-forwarding guide, for that matter, because you will still have incoming connections blocked on all your ports! In other words it is transparent for Layer 3 traffic (Layer 3 or Network-Layer/Internet-Layer is the level at which IP addressing is used). Click to Test Your Port Success-just go to Adjusting Internal Settings. An easy way to see if your port forwarding is configured properly or not is to see if you’re receiving incoming connections to BitComet by doing the following test. As shown below: Next, click: “Use the following IP address”.

表示された設定画面によって操作方法が異なります。 ご利用の商品の設定画面を確認してください。 設定画面の色、デザインは機種によって異なる場合があります。類似しているものを選択し … New Member. Port number in BitComet is at Tools>Options>Connection. The Static IP is the same IP Address as the one you saw in MS-DOS when you typed: BitComet's user interface → Detailed Info Pane →, When there is an active BT task in the tasklist, check the Detailed Info Pane →. So, as an example, using the IP addresses from the topology in the figure above, you will have to forward the listen port on Router1 towards 192.168.0.15. Start up Bitcomet, select "Tools" and then "Options." Every device that uses the internet sends its packets of data through specific ports. This sub-section is intended only for users who have 2 cascaded routers (daisy-chained). 變更 ), 您的留言將使用 Twitter 帳號。 The problem with Universal Plug and Play is that it's not supported by all routers, and different/incompatible implementations of the UPnP protocol are included in many routers. That is why it needs a rule set in its configuration settings, which says something of the type: “Packets incoming on port no. First, no matter which brand your router is, you will need to set up a static IP on the PC that will be using BitComet. Error- follow all steps. In the menu at the top of your screen, click, حسنا , في صورة آمتلاكي لمودام سجام 800 USB , كيف أتمكن من فتح Port أو ماهو البورت الدي من الأفضل آختياره , علم أن bitcomet يعمل الآن على البورت 24073 ؟.